HOBBYMATE Noble NB4 FGR4S V2 Receiver Bidirectional Receiver 4

Description: FlySky FGr4S V2 Receiver for Noble FS-NB4 / Noble Pro Transmitter Traxxas HPS HPI RC Car BoatEasy to bind and very fast link-up, quick and extremely stable in performanceUltra-small size and ultra-light weight, Dimensions: 25.5 * 22 * 17.3 mm; Weight: 5.1g; Effectively save space and reduce item's weight-bearingThe receiver supports PPM/i-bus/PWM data output, suitable for AFHDS3 system remote controller Product Description Flysky Noble NB4 Noble Pro Transmitter Receiver FGr4s V2 The FGr4S uses AFHDS 3 (Third Generation Automatic Frequency Hopping Digital System). It uses a internal single antenna with two way transmission capabilities and is designed to be compact and easy to install. It can output standard PPM,PWM 、i-BUS and S.BUS. Flysky noble nb4 noble pro receiver fgr4s v2 diagram To ensure a strong signal make sure that the receiver is mounted with its antenna vertical. CH 1 - CH 4: Connects the servos, power supply or other components. i-BUS/S.BUS: Output i.BUS/S.BUS signal, connect sensor and expansion module. After the transmitter is updated, if the code cannot be matched with the receiver, it is necessary to update the receiver. 1. Short circuit bind and its separated signal pins with bind cable;（It has been signed in the Receiver overview part） 2. Power on the receiver to enter the update mode) LED light of the receiver changes from 3 flash and 1 off）, unplug the bind cable, and select forced update at the transmitter. 3. The LED light of the receiver changes from 3 flash and 1 off to slow flash, the update is completed. Binding process for Flysky noble nb4 noble pro transmitter receiver FGr4s V2 Receiver Flysky noble nb4 receiver binding process and fail safe setup Binging 1. Insert the bind cable into the receivers BIND port; 2. Plug the power cable into any other port, and the the receiver's LED will start to flash indicating that it has entered bind mode. 3. Put the transmitter into bind mode; (See the transmitter's instruction manual for more information) 4. Binding is successful when the receiver's LED starts to flash slowly. Remove the power and bind cables from the receiver. If the transmitter is bidirectional the receiver status indicator will not flash slowly. 5. Reconnect the power cable to the receiver. 6. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again. Failsafe setup The failsafe function is used to output the channel according to the out-of-control protection value after the receiver loses its signal and is out of control to protect the model and personnel. • If the transmitter has not set the output of the failsafe channel value, after the receiver enters the out-of-control state, PWM, PPM, i-bus will not output, and the S.BUS will keep the last output; if the transmitter is set with the failsafe, follow the transmitter channel setting value Output. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no promise that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. EU DoC Declaration Hereby, Flysky Technology co., ltd] declares that the Radio Equipment [FGr4S] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: www.flysky-cn.com. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. Flysky INr4-GYB Gyro Receiver is available for Noble NB4, Noble Pro and Noble Lite, need to buy separately, check ASIN: B09XBG1KTS transmitter AFHDS3 (NB4,NB4 Lite etc.). The INr4-GYB receiver adopts Flysky's third-generation automatic frequency hopping digital system (AFHDS 3) It uses a single-antenna bidirectional transmission system ,with built-in gyroscope and is uniquely designed to install and output PWM/PPM/i-bus/S.BUS/i-bus2 in signals. It supports all AFHDS3 transmitter Flysky RC Gyro Receiver INr4-GYB for Noble NB4, Noble Pro, Noble Lite Radio Controllers INr4-GYB product ASIN: B08HWBBTKV Flysky Gyro Receiver INr4-GYB for Noble NB4, Noble Pro, Noble Lite Rc Transmitter The only gyro receiver for Flysky AFHDS3 protocol surface transmitters PWM Channels: 4 RF: 2.4GHz ISM 2.4G Protocol: AFHDS 3 Antenna: Single Antenna Input Power: 3.5~ 9V Data Output: PWM/PPM/i-bus/S.BUS/i-bus2 Online Update: Yes Dimensions: 17*29*16. 6mm Weight: 6.5g Certification: CE，FCC ID:N4ZINR4GYB0 Flysky RC Noble NB4 Gyro Receiver 4 Channels INr4 GYB, for Flysky NB4, Noble Lite, Noble Pro Radio Transmitter AFHDS 3 Model FGR4S V2 FGR4P FGR4 FGR8B INr4-GYB Channels 4 4 4 8 4 Protocol AFHDS 3 AFHDS 3 AFHDS 3 AFHDS 3 AFHDS 3 Model rc car / rc boat rc car / rc boat rc car / rc boat rc car / rc boat rc car / rc boat

Price: 60.99 USD

Location: Denver, Colorado

End Time: 2024-11-10T23:59:53.000Z

Shipping Cost: 0 USD