SOUNDSTREAM AR1.5000D MONOBLOCK CLASS D CAR AUDIO SUB AMP AMPLIFIER 5000W MAX

Description: SOUNDSTREAM AR1.5000D MONOBLOCK CLASS D CAR AUDIO SUB AMP AMPLIFIER 5000W MAX 1-OHM MINIMUM IMPEDANCE STABILITYAn amplifiers impedance stability is its ability to continuously power speaker(s) of no less than the given impedance per channel, without the risk of damage. Subwoofers are available in a variety of voice coil configurations and impedances, so be sure yours will be no less than 1-ohm. LOW LEVEL RCA INPUT & PRE-AMP OUTPUTConnect the low level (pre-amp) audio output of the car stereo to the amplifier, using good quality twisted pair RCA interconnect cables. The amplifiers pre-amp output daisy-chains the audio signal to multiple amplifiers of complex audio systems. ACTIVE 12DB/OCTAVE CROSSOVERS & PHASE SHIFT Active crossovers built into an amplifier are the most efficient type of crossovers to use in car audio systems. Active crossovers protect speakers from damage by harmful frequencies, and preserve optimum performance. MILITARY GRADE FR-4 PCB W/ MOSFET POWER SUPPLY FR-4 circuit board substrate is a woven fiberglass cloth impregnated with an epoxy resin, providing good electrical insulation properties and heat resistance exceeding 260OF. MOSFET power supply is the stable & efficient conversion of a vehicles Direct Current (DC) power to Alternating Current (AC) power for speakers. DASH MOUNT CONTROL Dash mountable control is included with this amplifier can be mounted anywhere in the vehicle, but near the driver seat is recommended. The gain level of the Arachnid monoblock can be adjusted on-the-fly to accommodate various music styles & your listening preference. DIRECT SHORT, THERMAL, & OVERLOAD PROTECTION Conventional amplifier circuitry include a self-preservation mode, which temporarily shuts down the amplifier, protecting it from stress and risk of damage. Protection triggers include speaker output direct short, speaker impedance less than the amplifiers stability, or other unknown conditions causing the amplifier internal temperature to rise to unsafe levels. SPECIFICATIONSAR1.5000DMax Power5,000 WattsRMS Power @ 4Ω500W x 1RMS Power @ 2Ω900W x 1RMS Power @ 1Ω1,500W x 1 (1Ω)Active Low Pass Crossover32-300Hz 12dB/OctaveActive Subsonic Crossover10-50Hz 12dB/OctaveVariable Phase Shift0-180°Total Harmonic Distortion<0.3%Frequency Response15-500HzSignal-to-Noise Ratio105dBInput Sensitivity200mV-6VDimensions (8.75″W x 2.25″ H)13.50″ 1-OHM MINIMUM IMPEDANCE STABILITYAn amplifiers impedance stability is its ability to continuously power speaker(s) of no less than the given impedance per channel, without the risk of damage. Subwoofers are available in a variety of voice coil configurations and impedances, so be sure yours will be no less than 1-ohm. LOW LEVEL RCA INPUT & PRE-AMP OUTPUTConnect the low level (pre-amp) audio output of the car stereo to the amplifier, using good quality twisted pair RCA interconnect cables. The amplifiers pre-amp output daisy-chains the audio signal to multiple amplifiers of complex audio systems. ACTIVE 12DB/OCTAVE CROSSOVERS & PHASE SHIFT Active crossovers built into an amplifier are the most efficient type of crossovers to use in car audio systems. Active crossovers protect speakers from damage by harmful frequencies, and preserve optimum performance. MILITARY GRADE FR-4 PCB W/ MOSFET POWER SUPPLY FR-4 circuit board substrate is a woven fiberglass cloth impregnated with an epoxy resin, providing good electrical insulation properties and heat resistance exceeding 260OF. MOSFET power supply is the stable & efficient conversion of a vehicles Direct Current (DC) power to Alternating Current (AC) power for speakers. DASH MOUNT CONTROL Dash mountable control is included with this amplifier can be mounted anywhere in the vehicle, but near the driver seat is recommended. The gain level of the Arachnid monoblock can be adjusted on-the-fly to accommodate various music styles & your listening preference. DIRECT SHORT, THERMAL, & OVERLOAD PROTECTION Conventional amplifier circuitry include a self-preservation mode, which temporarily shuts down the amplifier, protecting it from stress and risk of damage. Protection triggers include speaker output direct short, speaker impedance less than the amplifiers stability, or other unknown conditions causing the amplifier internal temperature to rise to unsafe levels. SPECIFICATIONSAR1.5000DMax Power5,000 WattsRMS Power @ 4Ω500W x 1RMS Power @ 2Ω900W x 1RMS Power @ 1Ω1,500W x 1 (1Ω)Active Low Pass Crossover32-300Hz 12dB/OctaveActive Subsonic Crossover10-50Hz 12dB/OctaveVariable Phase Shift0-180°Total Harmonic Distortion<0.3%Frequency Response15-500HzSignal-to-Noise Ratio105dBInput Sensitivity200mV-6VDimensions (8.75″W x 2.25″ H)13.50″eBay integration by

Price: 139.48 USD

Location: Rosemead, California

End Time: 2024-01-20T19:06:19.000Z

Shipping Cost: 0 USD